Call Today 800-627-1033



Mercury Contactors

Replace Your Mechanical Heater Load Contactors with Top Quality Mercury Contactors



Two-Pole Mercury Contactor
2-pole		 Three-Pole Mercury Contactor
3-pole


Click Here for Technical Information on Mercury Contactors
Click here for Technical Information on Mercury Contactors.

Mercury Displacement Contactors are all designed and built to meet the most exacting demands of industry. Their service life is equal to that of the solid state contactor, even under adverse conditions of temperature, dust and moisture. Each pole is hermetically sealed with high quality glass-to-metal seals to prevent moisture damage and voltage breakdown through the protective coating. Mercury Contactors are available in single or multiple pole units and in several coil voltages. Purchase the best contactors.


Advantages over mechanical contactors:

  • Superior performance and reliability for longer life and durability.
  • More compact size for easy installation.
  • Lower, predictable contact resistance.
  • Handles a variety of loads for increased design flexibility.
  • Lower coil power requirements.
  • Minimal derating due to higher ambient temperatures.
  • Quieter action.
 Mercury Contactor

35/60-Amp Specifications (Normally Open units):

  • Operate Time: 50 milliseconds
  • Release Time: 80 miliseconds
  • Contact Resistance:
       35-Amp = .003 ohm (after cycling under load)
       60-Amp = .002 ohm (after cycling under load)
  • Dielectric Withstand: 2500 VAC RMS
  • Longevity: millions of cycles
  • Temperature Range: -35°C to 85°C
  • Coil Terminals: #6 binding head screws
  • Load Terminals: pressure connectors for A.W.G. #4-#14 on 35-Amp units and A.W.G. #2-#8 on 60-Amp units

100-Amp Specifications (Normally Open units):

  • Operate Time: 50 milliseconds
  • Release Time: 80 miliseconds
  • Contact Resistance: .001 ohm (after cycling under load)
  • Dielectric Withstand: 2500 VAC RMS
  • Longevity: millions of cycles
  • Temperature Range: -35°C to 85°C
  • Coil Terminals: #6 binding head screws
  • Load Terminals: pressure connectors (standard accepts A.W.G. #2-#12)
1 POLE - NORMALLY OPEN
LOAD
RATE		 VOLTAGE VOLT AMPERES
A/P		 POWER
(watts)		 PART
NO.
35-AMP 120VAC 6.4 3.5 35NO-120A
24VDC 3.3 3.3 35NO-24D
240VAC 6.2 3.8 35NO-220A
60-AMP 120VAC 5.8 2.9 60NO-120A
24VDC 3.3 3.3 60NO-24D
240VAC 5.9 3.5 60NO-220A
100-AMP 120VAC 16.4 7.1 100NO-120A
24VDC 8.9 8.9 100NO-24D
240VAC 32.2 7.5 100NO-220A

 

2 POLE - NORMALLY OPEN
LOAD
RATE		 VOLTAGE VOLT AMPERES
A/P		 POWER
(watts)		 PART
NO.
35-AMP 120VAC 12.8 7.0 235NO-120A
24VDC 6.6 6.6 235NO-24D
240VAC 12.4 7.6 235NO-220A
60-AMP 120VAC 11.6 5.8 260NO-120A
24VDC 6.6 6.6 260NO-24D
240VAC 11.8 7.0 260NO-220A
100-AMP 120VAC 32.8 14.0 2100NO-120A
24VDC 17.8 17.8 2100NO-24D
240VAC 32.2 15.0 2100NO-220A


3 POLE - NORMALLY OPEN
LOAD
RATE		 VOLTAGE VOLT AMPERES
A/P		 POWER
(watts)		 PART
NO.
35-AMP 120VAC 19.2 10.5 335NO-120A
24VDC 9.9 9.9 335NO-24D
240VAC 18.6 11.4 335NO-220A
60-AMP 120VAC 17.4 8.7 360NO-120A
24VDC 9.9 9.9 360NO-24D
240VAC 17.7 10.5 360NO-220A
100-AMP 120VAC 49.2 21.3

3100NO-120A
24VDC 26.7 26.7 3100NO-24D
240VAC 48.3 22.5 3100NO-220A


4 POLE - NORMALLY OPEN
LOAD
RATE		 VOLTAGE VOLT AMPERES
A/P		 POWER
(watts)		 PART
NO.
35-AMP 120VAC 25.6 14.0 425NO-120A
24VDC 13.2 13.2 425NO-24D
240VAC 24.8 15.2 425NO-220A
60-AMP 120VAC 23.2 11.6 460NO-120A
24VDC 13.2 13.2 460NO-24D
240VAC 23.6 14.0 460NO-220A

 

 

TYPICAL APPLICATIONS


LIGHTING

 

GENERAL APPLICATIONS

ELECTRICAL HEATERS

FOOD INDUSTRY EQUIPMENT

 

SPECIALTY APPLICATIONS

 

 

Our mercury contactors are comparable with the following brands: ABB, ACT, Adams & Westlake, AEC, Aleph International, American Electronic, American Zettler, Amperite, ASB, ASI, ATC, CCI, Clare, Comus, Crouzet, Cougar Electronics, Dare, DME, Durakool, Eaton, Gama Electronics, Gavazzi, Gunther, Hamlin, Hasco, Leach, magnecraft, MDI, Mecury Switches, Micropac, MSI, Omega, Ogden, Panasonic, Phoenix Contact, SE Relays, Teledyne, tempco, Thermal Devices, Tyco, VB Controls, Vertex, Watlow.


art element

Manufacturers of High-Quality Products for the Plastics Molding Industry

Home | Request a Quote | Place an Order | Product Index | Online Catalog | Barrels & Screws | Electrical Products | Hoses & Fittings | Molding Accessories | SDS Sheets | Credit Application | Terms & Conditions | About Us | Contact Us 
 

SERVICES FOR PLASTICS, INC.
800-627-1033

7925 N. Clinton St., Fort Wayne, IN 46825-3113, USA
E-mail: Sales@ServicesForPlastics.com
Contact Webmaster regarding content or link problems
Copyright 1997-2024 | Services For Plastics, Inc. | All rights reserved. | Privacy Policy