Bunting Magnetics Gravity In-Line Magnets allow you to utilize our powerful plate magnets where material is under gravity flow. For effective tramp capture, spouting should be angled no more than 60° for horizontal.
General Materials: 13 Ga. 302/304 stainless steel with
standard size tube ends. Magnet Material: High-density Ceramic (CR) permanent
magnetic material. Rare Earth (NE) models available. Magnet Design: Standard Plate Magnet with 400 series
stainless steel exposed pole face. Other face styles available. Construction: Housing seam welded into an integral unit.
Magnet furnished with hinge, latches, and silicone gasket.
Compression couplings provided for installation. Special
adapters available upon request. Method of Cleaning: manual, from outside of housing,
utilizing hinged swing-away magnet. Self-cleaning models
available. Sizes: Available in 2" to 10" line sizes.
Special sizes available upon request
GRAVITY IN-LINE MAGNETS
(Rare Earth)
PART
NO.
LINE OD
GIM-5-NE
5"
GIM-6-NE
6"
GIM-8-NE
8"
GIM-10-NE
10"
Pneumatic In-Line Magnets
Pneumatic In-Line Magnets from Bunting Magnetics are built for use in dilute phase pneumatic conveying systems. They can be installed easily with optional factory supplied compression couplings and work best in horizontal runs with the plate magnet down to take advantage of material stratification.
General Materials: 11 Ga. 302/304 stainless steel with
standard size tube ends. Magnet Material: High-density Ceramic (CR) permanent
magnetic material. Rare Earth (NE) models available. Magnet Design: Standard Plate Magnet with 400 series
stainless steel exposed pole face. Other face styles available. Construction: Housing seam welded into an integral unit.
Magnet furnished with hinge, latches, and silicone gasket.
Compression couplings provided for installation. Special
adapters available upon request. Method of Cleaning: manual, from outside of housing,
utilizing hinged swing-away magnet. Self-cleaning models
available. Sizes: Available in 5" to 12" line sizes.
Special sizes available upon request
PNEUMATIC IN-LINE MAGNETS
(Ceramic)
PART
NO.
LINE OD
PIM-2-CR
2"
PIM-3-CR
3"
PIM-4-CR
4"
PIM-5-CR
5"
PIM-6-CR
6"
PIM-8-CR
8"
PIM-10-CR
10"
PNEUMATIC IN-LINE MAGNETS
(Rare Earth)
PART
NO.
LINE OD
PIM-2-NE
2"
PIM-3-NE
3"
PIM-4-NE
4"
PIM-5-NE
5"
PIM-6-NE
6"
PIM-8-NE
8"
PIM-10-NE
10"
Torpedo In-Line Magnets
Bunting Magnetics Torpedo In-Line Magnets provide magnetic protection for vacuum systems. By clamping directly into flexible hoses to capture ferrous contaminants, the compact In-Line Torpedo Magnet is an ideal option for use between gaylords and vacuum loaders or wherever overhead space is limited. Torpedo In-Line Magnets feature space-saving design and permanent Rare Earth magnets for high-energy tramp iron capture and holding power.
Unrestricted flow and superior protection.
Ideal for vacuum systems
High-density Rare Earth (NE) magnet material.
TORPEDO IN-LINE MAGNETS
PART
NO.
LINE OD
TIM-15
1.5"
TIM-20
2"
TIM-25
2.5"
Center Flow Magnets
Center Flow Magnets from Bunting Magnetics are ideal for use in dilute phase pneumatic conveyor systems, handling materials that are non-abrasive or not subject to damage by impact. Can be installed easily in any position or angle with factory supplied compression fittings. Recommended installation location is in long vertical runs. This is because air is more homogenous and distributed throughout the cross section of pipe, exposing the conveyed material and any tramp metal to the full surface of the magnetic cartridge. Center Flow Magnets can be used in horizontal or sloping runs when necessary or required by a specific application.
General Materials: 11 Ga. 302/304 stainless steel with
standard size tube ends. Magnet Material: High-density Ceramic (CR) permanent
magnetic material. Rare Earth (NE) models available. Magnet Design: Standard Plate Magnet with 400 series
stainless steel exposed pole face. Other face styles available. Construction: Housing seam welded into an integral unit.
Magnet furnished with hinge, latches, and silicone gasket.
Compression couplings provided for installation. Special
adapters available upon request. Method of Cleaning: manual, from outside of housing,
utilizing hinged swing-away magnet. Self-cleaning models
available. Sizes: Available in 3" to 6" line sizes.
Special sizes available upon request
CENTER FLOW MAGNETS
(Rare Earth)
PART
NO.
LINE OD
CFM-3-NE
3"
CFM-4-NE
4"
CFM-5-NE
5"
CFM-6-NE
6"
Our magnets are comparable to the following brands: A&A Magnetics, Accu-Feed, Bakker, Choumag, Dings, EFI, Eriez, Greenwood, Hamilton, Metal-Katcher, Nihon, National Magnetics, Novatec, Plastix, Prothermex, Pragati, Puritan, Shin-Etsu, Spaltech, Storch, Thompson.
Manufacturers of High-Quality
Products for the Plastics Molding Industry
7925 N. Clinton St., Fort Wayne, IN 46825-3113, USA
E-mail: sales@servicesforplastics.com
Contact Webmaster regarding content or link problems
Copyright 1997-2023 Services For Plastics, Inc. All rights reserved.