PLASTIC SERVICES
& EQUIPMENT

Home  |  Products   |  Brands  |  Place An Order  |  Request A Quote  | Promotions  |  Site Map  |  Contact Us

 

 

In-Line Magnets

 

Center Flow Magnets

Gravity In-Line Magnets

Pneumatic In-Line Magnets

Torpedo In-Line Magnets

 

 

 

Gravity In-Line Magnets

Bunting Magnetics Gravity In-Line Magnets allow you to utilize our powerful plate magnets where material is under gravity flow. For effective tramp capture, spouting should be angled no more than 60° for horizontal.

 

  • Unrestricted flow and superior protection.
  • Constructed from 13 Ga. 302/304 stainless steel.
  • High-density ceramic permanent magnet material. 
    (Rare Earth models available)

 

 

Gravity In-Line Magnet

GRAVITY IN-LINE MAGNETS
(Ceramic)

PART
NO.
LINE OD
GIM-5-CR 5"
GIM-6-CR 6"
GIM-8-CR 8"
GIM-10-CR 10"

SPECIFICATIONS

     General Materials:  13 Ga. 302/304 stainless steel with
     standard size tube ends.
     Magnet Material:  High-density Ceramic (CR) permanent
     magnetic material. Rare Earth (NE) models available.
     Magnet Design:  Standard Plate Magnet with 400 series
     stainless steel exposed pole face. Other face styles available.
     Construction:  Housing seam welded into an integral unit. 
     Magnet furnished with hinge, latches, and silicone gasket.
     Compression couplings provided for installation. Special 
     adapters available upon request.
     Method of Cleaning:  manual, from outside of housing, 
     utilizing hinged swing-away magnet. Self-cleaning models
     available.
     Sizes:  Available in 2" to 10" line sizes.

 
Special sizes available upon request

GRAVITY IN-LINE MAGNETS
(Rare Earth)

PART
NO.
LINE OD
GIM-5-NE 5"
GIM-6-NE 6"
GIM-8-NE 8"
GIM-10-NE 10"

 

 

 

Pneumatic In-Line Magnets

Pneumatic In-Line Magnets from Bunting Magnetics are built for use in dilute phase pneumatic conveying systems. They can be installed easily with optional factory supplied compression couplings and work best in horizontal runs with the plate magnet down to take advantage of material stratification.

 

  • Unrestricted flow and superior protection.
  • Constructed from 11 Ga. 302/304 stainless steel.
  • High-density ceramic permanent magnet material. 
    (Rare Earth models available)

 

Pneumatic In-Line Magnet

SPECIFICATIONS

     General Materials:  11 Ga. 302/304 stainless steel with
     standard size tube ends.
     Magnet Material:  High-density Ceramic (CR) permanent
     magnetic material. Rare Earth (NE) models available.
     Magnet Design:  Standard Plate Magnet with 400 series
     stainless steel exposed pole face. Other face styles available.
     Construction:  Housing seam welded into an integral unit. 
     Magnet furnished with hinge, latches, and silicone gasket.
     Compression couplings provided for installation. Special 
     adapters available upon request.
     Method of Cleaning:  manual, from outside of housing, 
     utilizing hinged swing-away magnet. Self-cleaning models
     available.
     Sizes:  Available in 5" to 12" line sizes.


Special sizes available upon request

PNEUMATIC IN-LINE MAGNETS
(Ceramic)

PART
NO.
LINE OD
PIM-2-CR 2"
PIM-3-CR 3"
PIM-4-CR 4"
PIM-5-CR 5"
PIM-6-CR 6"
PIM-8-CR 8"
PIM-10-CR 10"

PNEUMATIC IN-LINE MAGNETS
(Rare Earth)

PART
NO.
LINE OD
PIM-2-NE 2"
PIM-3-NE 3"
PIM-4-NE 4"
PIM-5-NE 5"
PIM-6-NE 6"
PIM-8-NE 8"
PIM-10-NE 10"
 

 

Torpedo In-Line Magnets

Bunting Magnetics Torpedo In-Line Magnets provide magnetic protection for vacuum systems. By clamping directly into flexible hoses to capture ferrous contaminants, the compact In-Line Torpedo Magnet is an ideal option for use between gaylords and vacuum loaders or wherever overhead space is limited. Torpedo In-Line Magnets feature space-saving design and permanent Rare Earth magnets for high-energy tramp iron capture and holding power.

 

  • Unrestricted flow and superior protection.
  • Ideal for vacuum systems
  • High-density Rare Earth (NE) magnet material. 

 

Torpedo In-Line Magnet

TORPEDO IN-LINE MAGNETS

PART
NO.
LINE OD
TIM-15 1.5"
TIM-20 2"
TIM-25 2.5"
 

 

Center Flow Magnets
Center Flow Magnets from Bunting Magnetics are ideal for use in dilute phase pneumatic conveyor systems, handling materials that are non-abrasive or not subject to damage by impact. Can be installed easily in any position or angle with factory supplied compression fittings. Recommended installation location is in long vertical runs. This is because air is more homogenous and distributed throughout the cross section of pipe, exposing the conveyed material and any tramp metal to the full surface of the magnetic cartridge. Center Flow Magnets can be used in horizontal or sloping runs when necessary or required by a specific application.

 

  • Constructed from 11 Ga. 302/304 stainless steel.
  • High-density ceramic permanent magnet material. 
    (Rare Earth models available)
  • Available in 3" to 6" line size.

 

Center Flow Magnet

CENTER FLOW MAGNETS
(Ceramic)

PART
NO.
LINE OD
CFM-3-CR 3"
CFM-4-CR 4"
CFM-5-CR 5"
CFM-6-CR 6"

SPECIFICATIONS

     General Materials:  11 Ga. 302/304 stainless steel with
     standard size tube ends.
     Magnet Material:  High-density Ceramic (CR) permanent
     magnetic material. Rare Earth (NE) models available.
     Magnet Design:  Standard Plate Magnet with 400 series
     stainless steel exposed pole face. Other face styles available.
     Construction:  Housing seam welded into an integral unit. 
     Magnet furnished with hinge, latches, and silicone gasket.
     Compression couplings provided for installation. Special 
     adapters available upon request.
     Method of Cleaning:  manual, from outside of housing, 
     utilizing hinged swing-away magnet. Self-cleaning models
     available.
     Sizes:  Available in 3" to 6" line sizes.

 
Special sizes available upon request

CENTER FLOW MAGNETS
(Rare Earth)

PART
NO.
LINE OD
CFM-3-NE 3"
CFM-4-NE 4"
CFM-5-NE 5"
CFM-6-NE 6"

 

 


Our magnets are comparable to the following brands: A&A Magnetics, Accu-Feed, Bakker, Choumag, Dings, EFI, Eriez, Greenwood, Hamilton, Metal-Katcher, Nihon, National Magnetics, Novatec, Plastix, Prothermex, Pragati, Puritan, Shin-Etsu, Spaltech, Storch, Thompson.

 

Your Next Barrel or Screw Is On Our Shelf...
Call Today! 800-627-1033

Home | Request A Quote | Place An Order | Product Index 
Barrels & Screws | Electrical Products | Hose & Fittings | Molding Accessories 
About PS&E
| Terms & Conditions | Credit Application
Contact Us | Request A Catalog | Online Catalog


PLASTIC SERVICES & EQUIPMENT


Fax:  800-482-4059
| E-mail:  sales@servicesforplastics.com | Address:  7925 N. Clinton St., Fort Wayne, IN 46825-3113, USA
Contact Webmaster regarding content or link problems.
Copyright 1997-2024 | Plastic Services & Equipment. | All rights reserved. | Privacy Policy